Dynamic-Mechanical Analysis Laboratory

Laboratory Director: Masoumeh Masoudi

Contact Number: 021-48662145

Email:  DMTA@ippi.ac.ir m.masoudi@ippi.ac.ir  ,  

 

Dynamic-Mechanical Analysis Laboratory

(Dynamic-Mechanical Analysis Laboratory)

 To complete its analytical equipment systems, the Polymer and Petrochemical Research Institute of Iran has equipped the Dynamic-Mechanical Analysis Laboratory with DMA-Triton and DMA Mettler Toledo instruments. In simple terms, DMA analysis involves applying an oscillatory force to a sample and analyzing the sample's response to it. The Storage Modulus, Loss Modulus, and Damping Factor (tan δ) of polymeric materials, which arise from their viscoelastic properties, are examined in this test. In this test, the sample is subjected to periodic stresses at a specified frequency (standard 1 Hz) in various modes such as bending, tensile, shear, and compression, under isothermal or non-isothermal conditions, with very low strain so that the material remains in its linear viscoelastic region. Changes in Storage Modulus, Loss Modulus, and the Damping Factor (tan δ), which is the ratio of Loss Modulus to Storage Modulus, are measured as a function of temperature. Using this test, transitions such as α, β, γ, etc., which result from various motions originating from the main chain or side groups attached to it, are observed. Additionally, the glass transition temperature (Tg), which is the temperature at which the sample's Storage Modulus drops suddenly and the Damping Factor increases sharply, can also be calculated and analyzed by this technique.

 

  • Type, Shape, and Dimensions of Samples:

Test Mode

Thickness (mm)

Width (mm)

Length (mm)

Number of Samples

Example

Tensile

<1

5-8

35

3

Film

Bending

Single/Dual

1-2

5-8

35

3

Plastic / Rubber

3 point

2-3

5-8

35

3

Composite

Compression

To be coordinated with the laboratory

5-8

5-8

3

Foam / Gel

Shear

<2

7-8

7-8

6

Hydrogel, Adhesive, etc.

 

 

·         Test Conditions

v Test Environment: Air

v Achievable Temperature Range: -150 to 250 degrees Celsius

v Frequency Range:  up to 180 Hz

v Heating rate or frequency step is determined by the customer.

v Samples must never melt or flow at the test temperature.

v Any irregularities or inconsistencies in sample dimensions will cause errors in the test results.

v  Powdered samples can also be used to determine Tg.

 

  • Standards Used:

ASTM E1640: Standard Test Method for Assignment of the Glass Transition Temperature by Dynamic Mechanical Analysis

ASTM D5023: Standard Test Method for Plastics: Dynamic Mechanical Properties: in Flexure (Three Point Bending)

ASTM D5026: Standard Test Method for Plastics: Dynamic Mechanical Properties: in Tension

 

  • Laboratory Equipment and Instruments:

 

·         DMA-Mettler Toledo (DMA1, Made in Switzerland)

·         DMA-Triton (Tritec 2000, Made in England)

logo
This research institute aims to develop the science and technology of polymer and petrochemical materials, train expert and research human resources, strengthen ties with industry and universities, meet the country's needs in this technical field, and participate in the global production of science.

Faculties

services

most visited

links

Address

Iran Polymer and Petrochemical Institute, Research Boulevard, Km 15, Tehran–Karaj Highway, Tehran, Iran

  • Email Address Iran
  • Phone Number 009821848666
  • Postal Code 13115-14977
  • Fax Number ۱٣۱۱۵-۱۴۹۷۷

© All rights of this site are reserved and belong to the Iranian Polymer and Petrochemical Research Institute.

طراحی و توسعه توسط سپهرگستر